Hydraulic Performance "When less acutally means more"
Launched in 2015, the KT360 Fluid Dynamics department is situated on site at Keltech. This customer centric engineering team has been created in response to market demand for the pursuit of efficiency and performance in Fuel and Hydraulic systems. Through years of experience and research, the team have developed best in class approaches. In doing so, KT360 Fluid Dynamics have enabled Keltech to become the partner of choice for renowned OEMs throughout the world.
Increase hydraulic performance
The KT360 Fluid Dynamics approach:
Conducted over a 4 week period, the KT360 team carried out several onsite pain diagnostics with the OEM customer. The pain for the customer in this case was a recent spike in hydraulic component failure experienced in the field operation. Warranty costs related to the hydraulics system of the machine had almost trebled in a 2 year period, the brand was also suffering as loyal customers that depended on machine reliability were beginning to become weary of the unreliability.
On investigation, the failed hydraulic components showed minute contaminants present in the fluid. It was suspected that these were the cause of the majority of failures. When analysed, the DNA of these containments ranged from machine build and assembly containments to other particles that most likely entered the system during the machine’s operation.
Based on machine type and expected operating conditions the KT360 team specified a NAS 9 cleanliness code recommendation for the hydraulic system (otherwise known as ISO4406). Achieving NAS 9 throughout the hydraulic system came with new challenges. For example, the team measured test samples of hydraulic oil direct from the manufacturer and to their surprise, a NAS 11 level of cleanliness was the best test result found. Alternative brands were trialled but it became apparent that hydraulic oil manufacturers themselves were failing to meet the NAS 9 level of cleanliness.
Through this investigation, the KT360 team developed a deeper understanding of 3rd party factors at play in the hydraulic system and set about creating robust solution.
Based on mathematical calculations, the team determined that the entirety of this particular hydraulic system would need to be filtered every 95 seconds during machine operation. This standard of filtration would drastically reduce the amount of contaminants entering hydraulic components.
The team analysed the current reservoir tank. A CFD test was carried out on the existing reservoir – this test is used to predict turbulence, sloshing and fluid path. The performance of the original reservoir tank could be described as inefficient at best. The fabrication had been designed from a structural view point but from a performance point of view it was rife with fluid dead-spots, heat dissipation issues, de-aeration issues etc.
A new hydraulic reservoir tank was designed by the KT360 team. The new design rectified the issues experienced above. The new design resulted in drastically increased efficiency and cut the required oil capacity requirement in half. Half the oil capacity; half the time required to filter the full hydraulic circuit.
The team then set their sight on the hydraulic filtration componentry that would be fitted to the reservoir tank. In partnership with our chosen supplier, all performance and efficiency metrics were reviewed. Off the shelf componentry was first sampled, suitable cost effective options were selected for parts such as gauges, sensors, filler necks and caps, etc. However when it came to the filter option, it was agreed that a bespoke solution was required.
This bespoke filter design solution is something which is unique to our partner, their flexible approach to manufacturing means machine tailored filter solutions can be made in high or low volume at a competitive cost base which are specifically designed to suit your machine (unique customer branding also available).
It is important to note, that for the duration of this project the customer was involved and informed every step of the way. With the new integrated reservoir tank now designed, real life trials were conducted. The customer manufactured two demo models for field trials which would be kept under close observation for a 6 month period. Both demo models would run in identical conditions during this period. Demo model 1 used the current hydraulic reservoir tank and circuit whilst demo model 2 was fitted with the KT360 design version.
After 6 months of field trails both machines were decommissioned and returned to our customer. From there, the full hydraulic circuits of both were removed and sent for analysis. The results were as we expected: Demo model 1 had what was classed as “moderate wear” to key hydraulic components/ Demo model 2 was classed as “no wear” to key hydraulic components.
The project had been a success. The end customer modified all new builds to use the KT360 designed integrated reservoir tank. 1 year since the serial introduction of this system and we have had the feedback that “warranty claims related to hydraulic component failure are drastically reduced, practically to the point of non-existence”. There has also been some interesting by-product benefits; there has been a significant weight reduction to the machine, a significant reduction in the space required to house the hydraulic reservoir tank and finally the cost of the reservoir tank has reduced as it is now approximately 50% smaller than the original model.
Enjoyed reading this post or want to find out more? Contact me on firstname.lastname@example.org or 00353864681333
"Blazing a Trail" Emma Daly.
Rathgormack born Emma Daily became Keltech’s very first female to enter our Welding Academy in November 2021. 8 months later Emma’s welding torch is burning bright. She has firmly become a key member of our Tank division and now fabricates fuel & hydraulic tanks for some of the largest construction equipment manufacturers in the world.
Our New Normal. 1st Female Production Team Leader.
It’s no secret that as a contract manufacturer with a core competency in sheet metal fabrication Keltech have traditionally operated in a male-dominated industry. But recently, this is becoming an outdated and inaccurate stereotype.
2021 Leaving Cert student says “Don’t follow the crowd, let the crowd follow you.”
In Ireland 2 out of every 3 leaving cert students now opt to enter higher education. Anecdotally we can all identify with the stories of those individuals who have drifted into courses that in hindsight were never a fit.
Welding- Automation & Craft Combine at Keltech
For over a decade global supply chains have struggled with a deficit in welding capacity. However the extreme market volatility caused by COVID-19 has now suddenly accelerated the issue to crisis point. The delta between demand for welded products and available welding capacity is now one of the largest issues facing industry in 2022.
Andy Hayes appointed CEO of Keltech.
Effective the 13th of December 2021, Andy Hayes takes on the role of CEO at Keltech. Andy takes up the leadership position having joined the business initially in 2018 as Chief Financial Officer. As part of the new company structure, founder Ray Breen will now move into the role of Chairperson.
"Tommy Farrell Flash Cup" Welding Competition Launched.
Last weekend we held our inaugural "Tommy Farrell Flash Cup" welding competition! This now annual event is an opportunity for our welders to display their skills in a competitive but fun format. The tournament is the brain child of Keltech's new in-house welding trainer Jeff Imrie.